Purchase Hotline 15815593375
After-sales Hotline 15207551155
Free samples, free customized after-sales guarantee
Contact Us
Tel: 89948454 / 83212351
Fax: 0086-755-89948030
Q Q: 2355542596
Email: hyd@szrl.net
Address: building a, No. 3, Hongling 1st Road, Liulian Shibi Industrial Zone, Pingdi Town, Longgang District, Shenzhen
Tank Filter Seal Jelly Glue
Tank filter tank glue Jelly glue Mainly used in tank filter to seal moisture and shock
Category:
Number: 1375406460476477440
Product Description
Product characteristics and application of liquid tank filter sealing jelly glue
HY9405# is a low-viscosity gel-like transparent two-component addition type silicone potting glue, which can be cured at room temperature or heated. faster feature. This product does not produce any by-products in the curing reaction, and can be applied to the surfaces of PC (Poly-carbonate) , PP , ABS , PVC and other materials and metals. Suitable for insulation, waterproofing and fixing of electronic accessories . Fully compliant with EU ROHS directive requirements.
Typical uses of sump filter seal jelly glue
-Slot type high efficiency filter
-Potting of electronic circuit boards, etc.
Liquid tank filter sealing jelly glue using process:
1. Before mixing, firstly mix components A and B in their respective containers thoroughly.
2. When mixing, the weight ratio of A component: B component = 1 : 1 should be observed .
3. HY9405# can be defoamed as needed. The mixed solution A and B can be stirred evenly and put into a vacuum container, defoamed at 0.08MPa for 5 minutes , and it can be used for perfusion .
4. The corresponding curing time should be maintained above the temperature given in the technical parameter table before and after curing. If the application thickness is thick, the curing time may exceed. Room temperature or heat curing is acceptable. The curing speed of the adhesive is affected by the curing temperature. It takes a long time to cure in winter. It is recommended to use heating to cure, 20 minutes at 80 ~ 100 ℃ , and about 8 hours at room temperature .
The following substances may hinder the curing of this product, or cause uncured phenomena, so it is best to apply it after a simple experimental verification. If necessary, the application area needs to be cleaned.
..incompletely cured condensed silicone..amine - cured epoxy
resin..solder flux
Technical parameters of tank filter seal jelly glue before and after curing:
|
Performance |
Component A |
component B |
|
|
solid change forward |
Exterior |
colorless transparent fluid |
black or blue |
|
Viscosity ( cps ) |
600 ± 200 |
800 ± 200 |
|
|
Hold do sex can |
A component: B component (weight ratio) |
1 : 1 |
|
|
Viscosity after mixing ( cps ) |
600 to 1000 _ _ |
||
|
Operational time ( hr ) |
3 |
||
|
Curing time ( hr , room temperature ) |
8 |
||
|
Curing time ( min , 80 ℃ ) |
20 |
||
|
solid change back |
Hardness ( shore A ) |
0 |
|
|
Thermal conductivity [ W ( m K ) ] |
≥0.2 _ |
||
|
Dielectric Strength ( kV/mm ) |
≥2 5 |
||
|
Dielectric Constant ( 1.2MHz ) |
3.0 to 3.3 |
||
|
Volume resistivity ( Ω cm ) |
≥1.0×10 16 |
||
|
Coefficient of Linear Expansion [ m/ ( m K ) ] |
≤2.2×10 -4 |
||
|
Flame retardant properties |
94-V 1 |
||
The above performance data are measured at 25 ℃ , 55% relative humidity after curing for 1 day. The company is not responsible for different data caused by different test conditions or product improvement.
Precautions for tank filter sealing jelly glue :
1. The rubber material should be sealed and stored. The mixed rubber should be used up at one time to avoid waste.
2. This product is a non-dangerous product, but do not enter it or see it.
3. After storage for a period of time, the glue may be delaminated. Please stir well before use, it will not affect the performance.
4. HY9405# will not cure when the glue contacts the following chemicals :
1 ) Organotin compounds and silicone rubber containing organotin.
2 ) Materials such as sulfur, sulfide and sulfur-containing rubber.
3 ) Amine compounds and amine-containing materials.
During use, please be careful to avoid contact with the above substances.
Tank Filter Seal Jelly Glue Packing Specifications:
HY9405 # : 25Kg / barrel 50kg 1 group
Tank Filter Seal Jelly Glue Storage and Transportation:
1. The storage period of this product is 1 year ( below 25 ℃ ).
2. Such products are non-dangerous goods and can be transported as general chemicals.
3. Products beyond the shelf life should be checked for abnormalities before use.
Keywords:
Contact Us
Tel: 89948454 / 83212351
Fax: 0086-755-89948030
Q Q: 2355542596
Email: hyd@szrl.net
Address: building a, No. 3, Hongling 1st Road, Liulian Shibi Industrial Zone, Pingdi Town, Longgang District, Shenzhen
Pay attention to us
